Welcome to the official website of ESTL!

Current location: Home > News > Certification news > Certification information

SJ/T 11778-2021 Industry Standard: Complete Compliance Guide

Editor:ESTL Category:Certification information Release time:2026-11-20 Click volume:7

Lithium Battery Safety Control for Electric Toothbrushes, Robot Vacuums, Massagers & Hand Warmers

SJ/T 11778-2021 Industry Standard: Complete Compliance Guide

How to manage the safety of lithium batteries built into electric toothbrushes, robot vacuums, massagers and hand warmers? The electronic industry standard SJ/T 11778-2021 gives the definitive answer. Issued on March 5, 2021 and implemented on June 1, 2021 under the administration of the Ministry of Industry and Information Technology (MIIT), it is a dedicated safety standard for lithium-ion cells and battery packs used in portable household appliances

1. Scope of SJ/T 11778 Standard

This standard applies to lithium-ion cells and battery packs for portable household appliances, divided into four product categories. The cleaning equipment category is frequently overlooked by manufacturers:

Category Typical Products
Portable personal cleaning & care appliances Electric toothbrushes, electric shavers, hair trimmers, skin exfoliators, etc.
Portable personal health care appliances Cervical/lumbar massagers, electric knee warmers, hand warmers, etc.
Portable site cleaning appliances Robot vacuums, floor washers, vacuum cleaners, window cleaners, electric irons, garment steamers; applicable for household, factory, mall, supermarket and station environments
Other similar appliances Lighting fixtures, adult products, air purifiers, humidifiers, indoor environmental monitoring instruments (temperature/humidity, formaldehyde, PM2.5 detectors)

Clear Division of Standards

  • Mobile phones, laptops and other portable electronic products: follow GB 31241
  • Household appliance batteries: follow SJ/T 11778 These two standards cannot replace each other, and test items are not interchangeable. Performance indicators such as capacity are covered by SJ/T 11757-2020 General Specification, while SJ/T 11778 only governs safety requirements

2. Test Items of SJ/T 11778

The standard establishes three-tier safety barriers: cell → battery pack → protection circuit. Passing only cell tests without verifying battery packs and protection circuits will lead to test failure.

Level Main Test Items
Cell Level (Bare Cell) High-temperature external short circuit, overcharge, forced discharge; mechanical & thermal abuse tests including compression, heavy-impact, thermal abuse, flame projection; environmental tests: low air pressure, temperature cycling, vibration, acceleration shock and drop test
Electrical Safety of Battery Pack Overvoltage charging, undervoltage discharging, overcurrent charging, overload, high-temperature operation, short circuit, high voltage resistance, unbalanced charging protection, current-carrying capacity of wiring. The core assessment is the validity of the battery pack’s built-in protection functions
System Protection Circuit Charge/discharge voltage & current control, charge/discharge temperature control, evaluating the rationality of parameter design for the whole set of protection circuits
Special Requirements for Battery Packs Water immersion, anti-ingestion design, stress relief, flame retardancy, plus verification of marking and Chinese warning statements

Critical Marking Requirement (Common Cause of Retesting)

The battery pack or its minimum packaging must carry Chinese warning labels. The battery body must be marked with: product name, model, rated capacity, rated energy, nominal voltage, charging limit voltage, polarity, manufacturer, production date and the implemented standard. Always check marking compliance before sample submission to avoid rework.

3. Certification & Test Lead Time

  1. Type Test: Per certification body rules, the testing period is normally 30 working days after sample receipt. Additional time for supplementary tests and retests is not included in this timeline.
  2. Test Report Only: If you only need a test report without formal certification, the cycle is shorter, depending on test scope and sample condition.
  3. Report Validity: If you apply for certification with an existing test report, the issuance date of the report shall be no more than 12 months prior to certification approval. The laboratory must hold valid qualifications, and the test items must fully cover certification requirements. Always control report validity when conducting tests first then certification.

4. Four Common Misunderstandings

  1. Misapplying electronic product standards to home appliances GB 31241 applies to portable IT electronics only. Household appliance batteries must follow SJ/T 11778; wrong standard selection will invalidate the whole test.
  2. Limiting the scope only to household use The standard clearly covers portable site cleaning equipment for household, factory, mall, supermarket and station scenarios. Commercial-use products are also within scope.
  3. Testing only cells while ignoring battery packs and protection circuits Qualified cells do not guarantee overall safety. Improper parameter design of the protection circuit creates major safety risks. Battery pack electrical safety and circuit tests are mandatory control items.
  4. Confusing safety standards with performance standards Capacity, cycle life and other performance metrics fall under SJ/T 11757, while safety evaluation follows SJ/T 11778. The two standards are independent and test items cannot be substituted.

5. Pre-Test Preparation Checklist

  1. Representative Samples: Test samples must be newly produced within 6 months to reflect mass-production quality.
  2. Wiring Resistance Control: When external wires are required for testing, the total wire resistance shall be controlled between 40 mΩ and 80 mΩ.
  3. Sufficient Sample Quantity: Prepare 3 pieces of samples for each test item. Calculate the total quantity and reserve extra samples for damage and retests.
  4. Complete Documentation: Prepare battery & pack specifications, protection circuit descriptions, marking artwork and warning text drafts. Document review and sample testing can be carried out simultaneously to shorten the whole schedule.

⚠ Important Reminder: SJ/T 11778-2021 is a recommended electronic industry standard. Mandatory national safety requirements for lithium batteries in household appliances shall follow the latest valid national GB standards. The selection of certification standards and certification arrangements shall strictly comply with the current certification rules of the certification body

Conclusion

Although lithium batteries for portable household appliances are small in size, they are used in close proximity to human bodies. Safety must be strictly enforced by complying with formal standards. If you have questions regarding lithium battery testing and certification for portable household appliances, please contact our ESTL testing team. We can help you confirm applicable standards, align test items, and arrange smooth testing and certification procedures.

Label: lithium-ion battery test for portable household appliances SJ/T 11778 battery safety test SJ/T 11778-2021
logo
Service HotlineWhatsApp:+86 13925582920
Address: 2nd Floor, Block B, Jinbaisheng Industrial Park, No. 2 Zongbu Road, Songshan Lake High-tech Industrial Development Zone, Dongguan, Guangdong, China Telephone: +86 13925582920 Fax: +86-0769-85075898 Mailbox: net03@gtggroup.com
Wechat Public Number

Focus on Wechat
Public Number

WhatsApp

Email

Wechat

WeChat

WeChat QR

Scan to follow us on WeChat

TOP